![]() |
VOLVO/LYNK&CO Diagnostic Software V44.50
Updates
Summary:
Added content for all models in the year of 2020.
Added ADAS (Advanced Driving Assistance System) Topology and Read version information for EVIN.
Extract commonly used special functions to the outermost menu for LYNK & CO models.
Optimized system entry content for S90L model.
New Functions:
Added content for all systems including update Data stream, Actuation test and DTC library for S90 (17-), V60 (19-), S90L, XC40, S60 (19-), V90 (17-), V90 Cross Country, XC60 (18-), XC90 (16-) and more models in the year of 2020.
Added special functions of Check A/C system for CCM (Climate Control Module), Reset the adaptation value of SCR system for DIESEL ENG (Diesel Engine), Quick test for EVAP purge valve and Read the values of fuel adaptation area for ECM (Engine Control Module), Start Park Assist Camera (PAC) to view for PAC (Park Assist Camera), Reset the DTCs in Steering Column Lock (SCL) for SCL (Steering Column Lock) module, Hybrid Front Axle Drive HyFAD standard for IGM (Inverter Generator Module), Calibrate Steering Angle Sensor (SAS) and sensors in Inertial Measurement Unit (IMU) for VDDM (Vehicle Dynamic Domain Master), Lock or Unlock SODL/SODR and Reset SODL/SODR to factory default settings for SODL/SODR (Side Obstacle Detection control module – Left/Right), Initialize the yaw rate offset compensation for SRS (Supplemental Restraint System) module, Reset adaptation values for Transmission Control Module (TCM) etc. of S90 (17-), V60 (19-), S90L, XC40, S60 (19-), V90 (17-), V90 Cross Country, XC60 (18-), XC90 (16-) and more models in the year of 2020.
Optimized Functions:
Optimized the function of Reset service lamp and Extract special functions to the outermost menu for handbrake maintenance position of LYNK & CO models.
Fixed Bugs:
None.
Software Instruction
Summary For The Covered Ecu:
Engine Control Module, Fuel System/Combined System, Transmission Control Module, Anti-lock Braking System, Supplemental Inflatable Restraint System, Burn Warm-Up Module, Central Electrical Module, Upper Electronic Module, Rear Electronic Module, Driver Information Module, Passenger Door Module, Climate Control Module, Phone Module, Information Control Module, Parking Brake Module, Headlight Control Module, Combined Instrument Panel, etc. systems.
Summary For The Covered Basic Function:
Reading ECU Information
Reading DTCs
Clearing DTCs
Reading Vehicle Running Data
Vehicle Component Operation Test
Summary For The Covered Special Function:
ECM (Gas Engine)
Throttle matching
Reset adjusted value
DIESEL ENG (Diesel Engine)
Reset adjusted value
Program the utmost optimized parameter
Reset particle filter odometer
EGR valve adaption
Carbon particle, particle holder burning
Reset particle filter counter
Adjust particle filter differential pressure sensor
Reset fuel counter
Adjust throttle module
Adjust rotate pass throttle
Adjust air flow rate sensor
Adjust turbo control motor
Adjust fuel pressure control valve
Carbon particle burning
Program idle speed
TCM (Automatic Transmission)
Reset learned value to zero
Reset replacement of transmission oil counter
Reset adjusted value
Enable gear indication
Position sensor calibrate
Enable adaption
ABS/BCM (Anti-lock Brake)
Calibration (DSTC (Dynamic Stable Traction Control))
Check brake light switch adjustment
Read configuration
SRS (Airbag)
Calibrate passenger weight sensor
Check PAD light
CPM (Burn warm-up module)
Program additional heater and parking heater
CEM (Center Electronic Module)
Read warning causes
Reset factory setting
Program control module
Counter at low voltage reset to zero
Reset crash mode
GDL (Gaseous-Discharge Lamp) position sensor calibration
Program rear window wiper while parking
Read and program vehicle mode
Program short flash
Ignition switch key position
UEM (Upper Electronic Module)
Anti-theft alarm installation
Setup control unit, read setting value
REM (Rear Electronic Module)
Calibrate dual-xenon lamp position sensor
DIM (Driver Information Module)
Service light reset
Instrument test
Program service driving distance
Program service time
Program engine service time
Program temperature measure unit
Program travel ECU
Program clock
Program zero point
Program parking brake warning
Program seat belt reminder audio signal
Program dashboard lighting
Read programmed parameters
DSTC display
PDM (Passenger door module)
Initialize window
CCM (A/C Control Module)
Read programmable parameter
Motor stop final position self-adjustment
Calibrate climate control module (CCM)
Program CCM
Identify damper motor module (DMM)
Read electronic damper motor,actual/preset range and tolerance limit
Identify component belong to CCM in LIN network
Program seat temperature
Read programmable parameters
PHM (Phone Module)
Re-assemble battery
ICM (Information Control Module)
Program entertainment System control module
Program other settings
PBM (Parking Brake Module)
Calibrate angle sensor
Activate and maintenance
Reset clutch pedal counter
HCM (Headlight Control Module)
Position sensor calibration
CI (Combined Instrument Panel)
Service light reset.